We may earn a commission when you buy. The price stays the retailer's.

Advertising disclosure

How-to

How to use a pressure washer surface cleaner

A surface cleaner hides the jets and erases wand stripes, if the pump can feed it and you do not tip the shroud up while it is spinning.

Updated November 18, 2026 · By Eric

As an Amazon Associate I earn from qualifying purchases. The price you pay does not change. How this works.

A wand leaves stripes because the fan is narrower than the step you take. A surface cleaner puts two jets under a round housing and lets you walk the concrete the way you would mow a lawn. The housing also keeps you from seeing the jets, which is why the rules are strict: the deck has to match the pump, it has to stay flat, and it is a rinse tool, not a substitute for chemical on oil.

The wash order for a driveway is the driveway how-to. Which washer feeds which deck is the concrete driveway washer guide. Pavers use the same deck and then a different finish, in the paver guide. The housings themselves are compared in the surface cleaner buying guide.

Pick the deck from the ceilings, not the diameter

Bigger is faster only when the pump can spin the bar. A wide deck on a thirsty pump drags, pulses, and leaves a halo.

The Westinghouse PWSC12 is the electric deck. The listing says 12 inches, 3,000 PSI maximum, 2.3 GPM maximum, about 2 lb, compatible with most electric pressure washers, and not intended for gas units. Put it behind something like the Greenworks GPW2300, whose manual lists 1.2 GPM rated and a 2.3 GPM maximum at low pressure. You will be under or at that 2.3 GPM ceiling depending on the tip and the load. A 12-inch path is the right size for a patio or a small pad. It is a long day on a two-car drive. Do not bolt this deck to a gas cart because the quick connect happens to fit.

The Simpson 80165 is 15 inches. The Amazon listing describes a recommended minimum of 2,200 PSI and 2.3 GPM and a maximum of 3,700 PSI. The manual lists 3,700 PSI and 3.0 GPM maximum, and 4.5 lb. The listing has also mentioned 3.4 GPM. When the two numbers disagree, stay at or under the manual’s 3.0 GPM. Simpson has listed the model as discontinued. The Westinghouse WPX3400 at 3,400 PSI and 2.6 GPM, and the Simpson PS3228 at 3,300 PSI and 2.5 GPM, sit inside that PSI cap and under that 3.0 GPM line, and they clear the listing’s 2.3 GPM minimum. The BE B2565HGS at 2,500 PSI and 3.0 GPM is on the manual’s flow maximum. That is the edge, not spare capacity.

The Westinghouse 15-inch surface cleaner is rated to 3,400 PSI, about 4 lb, 1/4-inch quick connect, and the listing says gas and electric. It does not publish a GPM ceiling in the features we checked. Do not assume a 4 GPM pump is fine. If the number is not on the page, it is not a match you can defend.

The BE Whirl-A-Way 20-inch, model BE-2000WAWY on the listing, is rated to 4,000 PSI. GPM and weight were not in that short block. Width is the point, and width needs water. A 1.2 GPM electric will not make a 20-inch bar feel like a video. A gas washer around 3 GPM, staying under 4,000 PSI, is the class to pair it with. The BE washer’s 2,500 PSI is under that PSI ceiling. Its 3.0 GPM is a plausible feed, with the caution that this deck’s own GPM limit was not published.

The NorthStar 157115 at 4.0 GPM does not go on the Simpson 80165. Hot water is a separate question the deck may not be rated for. The 80165 manual figure we are using is 140°F. Do not run a hot-water machine into a cold-water deck and hope.

Before the deck touches the slab

Sweep. Sand left on the concrete becomes a blast medium the moment the jets start. Move mats and the car. Wet plants if you are using chemical.

Oil and black tire film still want a cleaner. The Krud Kutter driveway gallon, model 385466, says bleach-free and a 3 to 5 minute dwell on that listing. Apply with the soap tip or a pump sprayer, not with the surface cleaner. Let it sit without drying. The deck is the rinse. The soap guide separates that jug from bleach products that do not belong in the pump.

Connect the deck with the washer off and the pressure dumped. These cleaners use a 1/4-inch quick connect. Tug the fitting. A partial click becomes a flying coupler when the pump comes up.

Use a hose long enough that you are not dragging the machine across the clean section. The hose guide is the pressure rating. The JOEJET reel listing is 50 feet by 3/8 inch, 4,000 PSI, if you want the hose on a reel instead of a coil in the driveway. The hose still has to be rated for your washer. A 4,000 PSI hose is not a permission slip to exceed the deck.

The pass

Start the washer with the deck flat on the concrete, not tipped up in the air. Squeeze the trigger and let the bar spin before you walk. If it chatters and does not settle, you may be under the flow the deck wants, or a jet is clogged. Do not muscle a dead bar across the slab. You will leave arcs.

Walk in straight, overlapping paths. The next pass should cover the ring the shroud left, the same way a mower overlaps. Hovering writes a bar into the concrete that shows up when it dries. Stopping to talk writes a circle. Keep a steady pace you can actually hold for the whole drive.

Slopes: work so dirty water moves off the section you have not cleaned yet, or accept that you will rinse the bottom twice. Do not start at the bottom and blow the film uphill onto a clean strip.

The Simpson driveway note on this site is that the manual is blunt about not lifting a spinning deck. Tipping the housing exposes the jets. They will scar whatever they point at, including your boot. If you need to turn around, do it with the deck down. If you need to step off the concrete, release the trigger and let the bar stop first.

Edges, steps, and the inch against the garage door are wand work. A fan tip, moving, several inches off. The nozzle guide is yellow versus green versus white. A 0-degree tip is not an edge tool. It is a line you cannot rinse out.

When it misbehaves

A pulse usually means one jet is partly blocked. Shut the washer down, release pressure, and clean the nozzles. Running through a clog loads the pump and etches an uneven circle. If you do not know how that deck comes apart, stop and read its sheet rather than prying with a screwdriver you will lose inside the bar.

A deck that leaves a clean center and a dirty rim is overlap, pace, or height. These housings are not adjustable in a way this site is going to invent. Slow down and overlap more before you blame the PSI.

Sealed or painted concrete can peel under a surface cleaner just as it can under a wand. Test a corner. If the sealer was the look you wanted, you may be signing up to reseal. That is a decision to make while the slab is still dry.

Wood is the wrong default. The jets sit close to the board and the shroud hides them. The deck guide says most wood is better with a fan you can see. Composite makers often forbid pressure washing entirely. Follow that maker.

After

Rinse chemical off plants. Flush the soap system if you used it. Coil the hose without a kink. Look down the drive in low sun when the concrete is dry. Missed rings show then, and one more overlapping pass is cheaper than living with the stripes.

Store the deck where the jets will not get packed with mud. The next wash starts faster when the nozzles are open. The washer you used still needs whatever its manual says about pump saver if it will sit. The surface cleaner did not change that.

Watch a walkthrough

These are other people's tutorials. Press play to load the video from YouTube.

How To Pressure Wash A Concrete DrivewayEveryday Home Repairs

Questions people ask

Will a surface cleaner work on an electric washer?

The Westinghouse PWSC12 listing says it is for most electric washers and not for gas, at 3,000 PSI and 2.3 GPM maximum. A 12-inch path is slow on a two-car drive. A 20-inch deck behind a 1.2 GPM electric will not glide.

Can I put the Simpson 80165 on a 4 GPM pump?

No. The manual lists 3.0 GPM maximum and 3,700 PSI maximum. The NorthStar hot-water washer is 4.0 GPM. That pairing is over the deck.

Why does my driveway still look striped?

The passes did not overlap, or you hovered. Walk so the next circle covers the shroud line. Check the result in low sun after it dries.

Can I use one on a wood deck?

Usually no. The jets sit close and you cannot see them. The deck guide prefers a fan tip you can watch. Test a hidden board only if you accept the risk of fuzzy grain.

What if the deck pulses?

Shut down, release pressure, and clean the nozzles. A clogged jet is the usual cause, and it loads the pump. Do not keep running it to see if the pulse goes away.

Related guides