A pressure washer without the right tip is a different machine. The pump can be the one you meant to buy, and the surface still gets cut, or the soap never leaves the tank, because the brass in the end of the wand is wrong. Color is the quick language. The stamp on the tip is the part that has to match the pump.
This page is about the two sets in the nozzle and wand guide: the Simpson 80145 and the Simpson 80146. The angles below are those sets, not a promise that every brand dyes the fans the same way. Other brands sometimes use gray for a wide fan. If your tips came in the box with a washer, read that manual before you assume Simpson’s colors.
How hard the water hits, once the tip is chosen, is PSI and GPM. Where a wide fan is the whole method: the deck guide and the siding guide.
Color is the angle
On these Simpson sets the five tips are the five standard angles.
Red is 0 degrees. The stream does not fan. It is a cutting jet. People use it to chew a spot of gum or a paint drip, and they also use it to engrave a line in a driveway and a groove in a deck board. Fluid from a 0-degree tip can inject through skin. That is a medical problem even when the puncture looks small. Leave red in the holder until you have a reason and a surface that can survive a pencil-width scar.
Yellow is 15 degrees. It is a narrow fan for concrete when you keep it moving and stay several inches off. The driveway how-to allows a 15-degree tip on sound concrete and tells you to stop when aggregate shows. Yellow on vinyl or on a wood deck is how the damage photos happen. It is too tight for a lap and too tight for softwood.
Green is 25 degrees. This is the general rinse on many jobs: siding when you are moving, wood when you are not seeing fuzz, and the step down from yellow on concrete edges. It is still a focused fan. Distance matters as much as the color.
White is 40 degrees. This is the wide fan. Cars, vinyl defaults, railings, and any surface you are afraid of start here. It feels slow, which is why people switch to yellow and regret it. Slow and wide is often the correct wash.
Black is soap. It is a large opening that drops pressure so the pump’s soap pickup can draw chemical. It is not a rinse tip. If you rinse with black you will be there all day and the soap may not clear. If you soap with green, the pressure is too high for dwell and you can skip the soap circuit entirely.
The Amazon features for both sets list those angles. They do not list a sixth color. A turbo nozzle, if your washer included one, is a separate part. The Greenworks GPW2300 listing and the Ryobi AR2N1 listing mention a turbo tip in the washer box. A spinning jet is a scar risk on cedar and on vinyl. It is not “the green one, but faster.”
Orifice is the hole
Color does not tell you whether the tip fits the pump. Orifice does. The 80145 set is orifice 3.0, rated to 3,600 PSI and 212°F. The 80146 set is orifice 4.0, rated to 4,500 PSI and 212°F. The larger hole is not a stronger tip. On a small pump it lets pressure fall off, and the washer feels weak. On a pump that wants 4.0, a 3.0 tip can hold pressure too high and make the unloader work constantly.
Use the chart that came with the washer, or the chart Simpson publishes for that pump. Do not copy a neighbor’s tips because the colors matched. Two green tips can be different holes.
Quick connect on these sets is 1/4 inch. They are not a fix for a wand that uses a different end. Look at the coupler before you order a set because the color was on sale.
Which color for which job
Concrete driveways and flat pads can use yellow if you keep moving, or a surface cleaner so you are not choosing a wand tip for the whole slab. The surface cleaner guide is that path. Edges and the strip against the garage still need a fan on the wand. White or green for the delicate edge, yellow only on sound concrete.
Wood decks start at white or green, along the grain, far enough off the board that the grain does not fuzz. The deck guide says a surface cleaner often makes this worse because you cannot see the jets. Red and yellow are how zebra stripes get written into cedar.
Vinyl and other siding default to white. Green is as narrow as most walls should see. Spray downward. The vinyl mildew guide is the chemical half. The tip only rinses. Yellow and red lift laps and drive water into the wall.
Cars and paint stay on white, after the grit is rinsed off, so a mitt is not grinding sand. This site’s foam cannon, the MTM PF22 bundle, is a soap tool rated 1,100 to 5,000 PSI and 1.4 to 5.3 GPM on that listing. It does not replace the rinse tip, and the orifice still has to match the washer. The accessories guide says a foam cannon is a method, not a requirement.
Pavers are concrete-like until the joints. A 0-degree tip in a sand joint digs the joint out. That is the paver guide. Use a surface cleaner or a wide fan, not red.
The wand is not the tip
The Simpson 80149 is a 16-inch cold-water wand, up to 3,600 PSI, 140°F, with a 1/4-inch quick connect for the nozzle and an M22 end for the gun. It replaces a short lance. It does not reach a second story, and it does not change red into a safe tip.
The Simpson 80470 telescopes from 6 to 18 feet, with a harness, rated to 4,000 PSI and 8.0 GPM, cold water, 140°F. It is how you rinse a wall from the ground. A 0-degree or 15-degree tip on an 18-foot wand is a way to scar siding you can barely see. Wide fan only. Stay clear of overhead lines.
The Simpson 80148 gun is a separate part, rated to 4,500 PSI and 6.6 GPM on its listing. A gun does not choose the fan. The tip does. If you replace the gun, the wand and the tip still have to be rated for the washer.
Putting a tip on without a lecture
Relieve pressure before you swap. Turn the washer off, squeeze the trigger to dump the hose, and then pull the coupler back. Forcing a tip into a live quick connect is how people pinch a finger and how O-rings tear.
Click the tip, tug it, and point the wand at the ground for the first second. A red tip you thought was white announces itself immediately. If the fan looks like a needle, stop and look at the color again.
Soap order, if you are using a tank the label allows: black tip, apply, dwell, then a rinse color. Flush the black tip and the soap circuit with clear water. Leaving chemical in the pickup eats the parts the manual told you not to soak.
If the pressure feels wrong after a new set, check the orifice before you blame the pump. A 4.0 set on a machine charted for 3.0 is a common “my washer got weak” story. The pump did not change. The hole did.
Store the tips in the holder, red included, so the next wash does not start with whatever was left in the wand. The holder is the safety step. The color code only works if you can see it.